当前位置：首页 > news >正文

【源码分析】Linux内核ov13850.c

news 来源：原创 2025/7/13 1:30:52

这里写自定义目录标题

1、入口函数：__init sensor_mod_init
2、probe函数：ov13850_probe
- 2.1、初始化前的一些准备
- 2.2、设备初始化流程
源码如下

了解运行流程

1、入口函数：__init sensor_mod_init

驱动由 __init 开始 __exit 结束，ov13850摄像头的入口函数为sensor_mod_init，其中是按标准的I2C设备驱动注册；
i2c_add_driver本质是对i2c_register_driver做了一个简单的封装；

static int __init sensor_mod_init(void)
{return i2c_add_driver(&ov13850_i2c_driver);
}

ov13850_i2c_driver为ov13850设备结构体,其中关键的结构体成员作用如下：

of_match_table：用来配备设备树compatible属性（I2C 设备和驱动的匹配过程是由 I2C 核心来完成的）
probe：在匹配完成后执行改指向的函数；
id_table：在没有设备树的情况下匹配ID表

static struct i2c_driver ov13850_i2c_driver = {.driver = {.name = OV13850_NAME,.pm = &ov13850_pm_ops,.of_match_table = of_match_ptr(ov13850_of_match),},.probe          = &ov13850_probe,.remove         = &ov13850_remove,.id_table       = ov13850_match_id,
};

2、probe函数：ov13850_probe

在匹配完成后获取一些设备树的参数并初始化摄像头

2.1、初始化前的一些准备

打印驱动版本号；
为ov13850摄像头-i2c设备结构体申请内存；
从设备树获取摄像头的一些属性，如是否前摄后摄、摄像是否是广角等；
从设备树获取摄像头的一些配置管脚，如时钟、电源、复位、使能等；
获取设备树中自己用 pinctrl 建立的节点；

			 /*1、 打印驱动的版本 */dev_info(dev, "driver version: %02x.%02x.%02x",DRIVER_VERSION >> 16,(DRIVER_VERSION & 0xff00) >> 8,DRIVER_VERSION & 0x00ff);/*2、为ov13850摄像头-i2c设备结构体申请内存 */ov13850 = devm_kzalloc(dev, sizeof(*ov13850), GFP_KERNEL);if (!ov13850)return -ENOMEM;/*3、从设备树获取摄像头的一些属性，如是否前摄后摄、摄像是否是广角等 */ret = of_property_read_u32(node, RKMODULE_CAMERA_MODULE_INDEX,&ov13850->module_index);ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_FACING,&ov13850->module_facing);ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_NAME,&ov13850->module_name);ret |= of_property_read_string(node, RKMODULE_CAMERA_LENS_NAME,&ov13850->len_name);if (ret) {dev_err(dev, "could not get module information!\n");return -EINVAL;}ov13850->client = client;ov13850->cur_mode = &supported_modes[0];/*4、从设备树获取摄像头的一些配置管脚，如时钟、电源、复位、使能等 */ov13850->xvclk = devm_clk_get(dev, "xvclk");if (IS_ERR(ov13850->xvclk)) {dev_err(dev, "Failed to get xvclk\n");return -EINVAL;}ov13850->power_gpio = devm_gpiod_get(dev, "power", GPIOD_OUT_LOW);if (IS_ERR(ov13850->power_gpio))dev_warn(dev, "Failed to get power-gpios, maybe no use\n");ov13850->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);if (IS_ERR(ov13850->reset_gpio))dev_warn(dev, "Failed to get reset-gpios\n");ov13850->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW);if (IS_ERR(ov13850->pwdn_gpio))dev_warn(dev, "Failed to get pwdn-gpios\n");ret = ov13850_configure_regulators(ov13850);if (ret) {dev_err(dev, "Failed to get power regulators\n");return ret;}/*5、获取设备树中自己用 pinctrl 建立的节点*/ov13850->pinctrl = devm_pinctrl_get(dev);if (!IS_ERR(ov13850->pinctrl)) {ov13850->pins_default =pinctrl_lookup_state(ov13850->pinctrl,OF_CAMERA_PINCTRL_STATE_DEFAULT);if (IS_ERR(ov13850->pins_default))dev_err(dev, "could not get default pinstate\n");ov13850->pins_sleep =pinctrl_lookup_state(ov13850->pinctrl,OF_CAMERA_PINCTRL_STATE_SLEEP);if (IS_ERR(ov13850->pins_sleep))dev_err(dev, "could not get sleep pinstate\n");}

2.2、设备初始化流程

mutex_init：初始化互斥锁；
v4l2_i2c_subdev_init：使用V4l2驱动接口初始化i2c设备
ov13850_initialize_controls：初始化摄像头参数，将设备控件注册到V4l2子系统中；
__ov13850_power_on：摄像头上电初始化，设置配置时钟、电源、复位等引脚
ov13850_check_sensor_id：读取寄存器中的ID信息是否与驱动标定的一致；
media_entity_pads_init：初始化entity pad
4l2_async_register_subdev_sensor_common：注册v4l2_subdev设备，创建ov13850对应的Media Entity，创建设备节点

		/*1、初始化互斥锁 */mutex_init(&ov13850->mutex);sd = &ov13850->subdev;v4l2_i2c_subdev_init(sd, client, &ov13850_subdev_ops);ret = ov13850_initialize_controls(ov13850);if (ret)goto err_destroy_mutex;ret = __ov13850_power_on(ov13850);if (ret)goto err_free_handler;ret = ov13850_check_sensor_id(ov13850, client);if (ret)goto err_power_off;#ifdef CONFIG_VIDEO_V4L2_SUBDEV_APIsd->internal_ops = &ov13850_internal_ops;sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
#endif
#if defined(CONFIG_MEDIA_CONTROLLER)ov13850->pad.flags = MEDIA_PAD_FL_SOURCE;sd->entity.function = MEDIA_ENT_F_CAM_SENSOR;ret = media_entity_pads_init(&sd->entity, 1, &ov13850->pad);if (ret < 0)goto err_power_off;
#endifmemset(facing, 0, sizeof(facing));if (strcmp(ov13850->module_facing, "back") == 0)facing[0] = 'b';elsefacing[0] = 'f';snprintf(sd->name, sizeof(sd->name), "m%02d_%s_%s %s",ov13850->module_index, facing,OV13850_NAME, dev_name(sd->dev));ret = v4l2_async_register_subdev_sensor_common(sd);if (ret) {dev_err(dev, "v4l2 async register subdev failed\n");goto err_clean_entity;}pm_runtime_set_active(dev);pm_runtime_enable(dev);pm_runtime_idle(dev);return 0;

#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
static const struct v4l2_subdev_internal_ops ov13850_internal_ops = {.open = ov13850_open,
};
#endifstatic const struct v4l2_subdev_core_ops ov13850_core_ops = {.s_power = ov13850_s_power,.ioctl = ov13850_ioctl,
#ifdef CONFIG_COMPAT.compat_ioctl32 = ov13850_compat_ioctl32,
#endif
};static const struct v4l2_subdev_video_ops ov13850_video_ops = {.s_stream = ov13850_s_stream,.g_frame_interval = ov13850_g_frame_interval,
};static const struct v4l2_subdev_pad_ops ov13850_pad_ops = {.enum_mbus_code = ov13850_enum_mbus_code,//被subdev_do_ioctl的VIDIOC_SUBDEV_ENUM_MBUS_CODE调用。.enum_frame_size = ov13850_enum_frame_sizes,//被subdev_do_ioctl的VIDIOC_SUBDEV_ENUM_FRAME_SIZE调用。.enum_frame_interval = ov13850_enum_frame_interval,//被subdev_do_ioctl的VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL调用。.get_fmt = ov13850_get_fmt,//被subdev_do_ioctl的VIDIOC_SUBDEV_G_FMT调用。.set_fmt = ov13850_set_fmt,//被subdev_do_ioctl的VIDIOC_SUBDEV_S_FMT调用。.get_mbus_config = ov13850_g_mbus_config,
};static const struct v4l2_subdev_ops ov13850_subdev_ops = {.core    = &ov13850_core_ops,.video    = &ov13850_video_ops,.pad    = &ov13850_pad_ops,
};

源码如下

// SPDX-License-Identifier: GPL-2.0
/** ov13850 driver** Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd.** V0.0X01.0X01 add poweron function.* V0.0X01.0X02 fix mclk issue when probe multiple camera.* V0.0X01.0X03 add enum_frame_interval function.* V0.0X01.0X04 add quick stream on/off* V0.0X01.0X05 add function g_mbus_config*/#include <linux/clk.h>
#include <linux/device.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
#include <linux/regulator/consumer.h>
#include <linux/sysfs.h>
#include <linux/slab.h>
#include <linux/version.h>
#include <linux/rk-camera-module.h>
#include <media/media-entity.h>
#include <media/v4l2-async.h>
#include <media/v4l2-ctrls.h>
#include <media/v4l2-subdev.h>
#include <linux/pinctrl/consumer.h>#define DRIVER_VERSION			KERNEL_VERSION(0, 0x01, 0x05)#ifndef V4L2_CID_DIGITAL_GAIN
#define V4L2_CID_DIGITAL_GAIN		V4L2_CID_GAIN
#endif#define OV13850_LINK_FREQ_300MHZ	300000000
/* pixel rate = link frequency * 2 * lanes / BITS_PER_SAMPLE */
#define OV13850_PIXEL_RATE		(OV13850_LINK_FREQ_300MHZ * 2 * 2 / 10)
#define OV13850_XVCLK_FREQ		24000000#define CHIP_ID				0x00d850
#define OV13850_REG_CHIP_ID		0x300a#define OV13850_REG_CTRL_MODE		0x0100
#define OV13850_MODE_SW_STANDBY		0x0
#define OV13850_MODE_STREAMING		BIT(0)#define OV13850_REG_EXPOSURE		0x3500
#define	OV13850_EXPOSURE_MIN		2
#define	OV13850_EXPOSURE_STEP		1
#define OV13850_VTS_MAX			0x7fff#define OV13850_REG_GAIN_H		0x350a
#define OV13850_REG_GAIN_L		0x350b
#define OV13850_GAIN_H_MASK		0x07
#define OV13850_GAIN_H_SHIFT		8
#define OV13850_GAIN_L_MASK		0xff
#define OV13850_GAIN_MIN		0x10
#define OV13850_GAIN_MAX		0xf8
#define OV13850_GAIN_STEP		1
#define OV13850_GAIN_DEFAULT		0x10#define OV13850_REG_TEST_PATTERN	0x5e00
#define	OV13850_TEST_PATTERN_ENABLE	0x80
#define	OV13850_TEST_PATTERN_DISABLE	0x0#define OV13850_REG_VTS			0x380e#define REG_NULL			0xFFFF#define OV13850_REG_VALUE_08BIT		1
#define OV13850_REG_VALUE_16BIT		2
#define OV13850_REG_VALUE_24BIT		3#define OV13850_LANES			2
#define OV13850_BITS_PER_SAMPLE		10#define OV13850_CHIP_REVISION_REG	0x302A
#define OV13850_R1A			0xb1
#define OV13850_R2A			0xb2#define OF_CAMERA_PINCTRL_STATE_DEFAULT	"rockchip,camera_default"
#define OF_CAMERA_PINCTRL_STATE_SLEEP	"rockchip,camera_sleep"#define OV13850_NAME			"ov13850"static const struct regval *ov13850_global_regs;static const char * const ov13850_supply_names[] = {"avdd",		/* Analog power */"dovdd",	/* Digital I/O power */"dvdd",		/* Digital core power */
};#define OV13850_NUM_SUPPLIES ARRAY_SIZE(ov13850_supply_names)struct regval {u16 addr;u8 val;
};struct ov13850_mode {u32 bus_fmt;u32 width;u32 height;struct v4l2_fract max_fps;u32 hts_def;u32 vts_def;u32 exp_def;const struct regval *reg_list;u32 link_freq_idx;u32 bpp;
};struct ov13850 {struct i2c_client	*client;struct clk		*xvclk;struct gpio_desc	*power_gpio;struct gpio_desc	*reset_gpio;struct gpio_desc	*pwdn_gpio;struct regulator_bulk_data supplies[OV13850_NUM_SUPPLIES];struct pinctrl		*pinctrl;struct pinctrl_state	*pins_default;struct pinctrl_state	*pins_sleep;struct v4l2_subdev	subdev;struct media_pad	pad;struct v4l2_ctrl_handler ctrl_handler;struct v4l2_ctrl	*exposure;struct v4l2_ctrl	*anal_gain;struct v4l2_ctrl	*digi_gain;struct v4l2_ctrl	*hblank;struct v4l2_ctrl	*vblank;struct v4l2_ctrl	*test_pattern;struct v4l2_ctrl	*pixel_rate;struct v4l2_ctrl	*link_freq;struct mutex		mutex;bool			streaming;bool			power_on;const struct ov13850_mode *cur_mode;u32			module_index;const char		*module_facing;const char		*module_name;const char		*len_name;struct v4l2_fract	cur_fps;u32			cur_vts;
};#define to_ov13850(sd) container_of(sd, struct ov13850, subdev)/** Xclk 24Mhz*/
static const struct regval ov13850_global_regs_r1a[] = {{0x0103, 0x01},{0x0300, 0x00},{0x0301, 0x00},{0x0302, 0x32},{0x0303, 0x01},{0x030a, 0x00},{0x300f, 0x11},{0x3010, 0x01},{0x3011, 0x76},{0x3012, 0x21},{0x3013, 0x12},{0x3014, 0x11},{0x3015, 0xc0},{0x301f, 0x03},{0x3106, 0x00},{0x3210, 0x47},{0x3500, 0x00},{0x3501, 0x60},{0x3502, 0x00},{0x3506, 0x00},{0x3507, 0x02},{0x3508, 0x00},{0x350a, 0x00},{0x350b, 0x80},{0x350e, 0x00},{0x350f, 0x10},{0x3600, 0x40},{0x3601, 0xfc},{0x3602, 0x02},{0x3603, 0x48},{0x3604, 0xa5},{0x3605, 0x9f},{0x3607, 0x00},{0x360a, 0x40},{0x360b, 0x91},{0x360c, 0x49},{0x360f, 0x8a},{0x3611, 0x10},{0x3612, 0x27},{0x3613, 0x33},{0x3615, 0x08},{0x3641, 0x02},{0x3660, 0x82},{0x3668, 0x54},{0x3669, 0x40},{0x3667, 0xa0},{0x3702, 0x40},{0x3703, 0x44},{0x3704, 0x2c},{0x3705, 0x24},{0x3706, 0x50},{0x3707, 0x44},{0x3708, 0x3c},{0x3709, 0x1f},{0x370a, 0x26},{0x370b, 0x3c},{0x3720, 0x66},{0x3722, 0x84},{0x3728, 0x40},{0x372a, 0x00},{0x372f, 0x90},{0x3710, 0x28},{0x3716, 0x03},{0x3718, 0x10},{0x3719, 0x08},{0x371c, 0xfc},{0x3760, 0x13},{0x3761, 0x34},{0x3767, 0x24},{0x3768, 0x06},{0x3769, 0x45},{0x376c, 0x23},{0x3d84, 0x00},{0x3d85, 0x17},{0x3d8c, 0x73},{0x3d8d, 0xbf},{0x3800, 0x00},{0x3801, 0x08},{0x3802, 0x00},{0x3803, 0x04},{0x3804, 0x10},{0x3805, 0x97},{0x3806, 0x0c},{0x3807, 0x4b},{0x3808, 0x08},{0x3809, 0x40},{0x380a, 0x06},{0x380b, 0x20},{0x380c, 0x12},{0x380d, 0xc0},{0x380e, 0x06},{0x380f, 0x80},{0x3810, 0x00},{0x3811, 0x04},{0x3812, 0x00},{0x3813, 0x02},{0x3814, 0x31},{0x3815, 0x31},{0x3820, 0x02},{0x3821, 0x05},{0x3834, 0x00},{0x3835, 0x1c},{0x3836, 0x08},{0x3837, 0x02},{0x4000, 0xf1},{0x4001, 0x00},{0x400b, 0x0c},{0x4011, 0x00},{0x401a, 0x00},{0x401b, 0x00},{0x401c, 0x00},{0x401d, 0x00},{0x4020, 0x00},{0x4021, 0xE4},{0x4022, 0x07},{0x4023, 0x5F},{0x4024, 0x08},{0x4025, 0x44},{0x4026, 0x08},{0x4027, 0x47},{0x4028, 0x00},{0x4029, 0x02},{0x402a, 0x04},{0x402b, 0x08},{0x402c, 0x02},{0x402d, 0x02},{0x402e, 0x0c},{0x402f, 0x08},{0x403d, 0x2c},{0x403f, 0x7f},{0x4500, 0x82},{0x4501, 0x38},{0x4601, 0x04},{0x4602, 0x22},{0x4603, 0x01},{0x4800, 0x24}, //MIPI CLK control{0x4837, 0x1b},{0x4d00, 0x04},{0x4d01, 0x42},{0x4d02, 0xd1},{0x4d03, 0x90},{0x4d04, 0x66},{0x4d05, 0x65},{0x5000, 0x0e},{0x5001, 0x01},{0x5002, 0x07},{0x5013, 0x40},{0x501c, 0x00},{0x501d, 0x10},{0x5242, 0x00},{0x5243, 0xb8},{0x5244, 0x00},{0x5245, 0xf9},{0x5246, 0x00},{0x5247, 0xf6},{0x5248, 0x00},{0x5249, 0xa6},{0x5300, 0xfc},{0x5301, 0xdf},{0x5302, 0x3f},{0x5303, 0x08},{0x5304, 0x0c},{0x5305, 0x10},{0x5306, 0x20},{0x5307, 0x40},{0x5308, 0x08},{0x5309, 0x08},{0x530a, 0x02},{0x530b, 0x01},{0x530c, 0x01},{0x530d, 0x0c},{0x530e, 0x02},{0x530f, 0x01},{0x5310, 0x01},{0x5400, 0x00},{0x5401, 0x61},{0x5402, 0x00},{0x5403, 0x00},{0x5404, 0x00},{0x5405, 0x40},{0x540c, 0x05},{0x5b00, 0x00},{0x5b01, 0x00},{0x5b02, 0x01},{0x5b03, 0xff},{0x5b04, 0x02},{0x5b05, 0x6c},{0x5b09, 0x02},{0x5e00, 0x00},{0x5e10, 0x1c},{0x0102, 0x01}, //Fast standby enable{REG_NULL, 0x00},
};/** Xclk 24Mhz*/
static const struct regval ov13850_global_regs_r2a[] = {{0x0300, 0x01},{0x0301, 0x00},{0x0302, 0x28},{0x0303, 0x00},{0x030a, 0x00},{0x300f, 0x11},{0x3010, 0x01},{0x3011, 0x76},{0x3012, 0x21},{0x3013, 0x12},{0x3014, 0x11},{0x301f, 0x03},{0x3106, 0x00},{0x3210, 0x47},{0x3500, 0x00},{0x3501, 0x60},{0x3502, 0x00},{0x3506, 0x00},{0x3507, 0x02},{0x3508, 0x00},{0x350a, 0x00},{0x350b, 0x80},{0x350e, 0x00},{0x350f, 0x10},{0x351a, 0x00},{0x351b, 0x10},{0x351c, 0x00},{0x351d, 0x20},{0x351e, 0x00},{0x351f, 0x40},{0x3520, 0x00},{0x3521, 0x80},{0x3600, 0xc0},{0x3601, 0xfc},{0x3602, 0x02},{0x3603, 0x78},{0x3604, 0xb1},{0x3605, 0xb5},{0x3606, 0x73},{0x3607, 0x07},{0x3609, 0x40},{0x360a, 0x30},{0x360b, 0x91},{0x360c, 0x09},{0x360f, 0x02},{0x3611, 0x10},{0x3612, 0x27},{0x3613, 0x33},{0x3615, 0x0c},{0x3616, 0x0e},{0x3641, 0x02},{0x3660, 0x82},{0x3668, 0x54},{0x3669, 0x00},{0x366a, 0x3f},{0x3667, 0xa0},{0x3702, 0x40},{0x3703, 0x44},{0x3704, 0x2c},{0x3705, 0x01},{0x3706, 0x15},{0x3707, 0x44},{0x3708, 0x3c},{0x3709, 0x1f},{0x370a, 0x27},{0x370b, 0x3c},{0x3720, 0x55},{0x3722, 0x84},{0x3728, 0x40},{0x372a, 0x00},{0x372b, 0x02},{0x372e, 0x22},{0x372f, 0x90},{0x3730, 0x00},{0x3731, 0x00},{0x3732, 0x00},{0x3733, 0x00},{0x3710, 0x28},{0x3716, 0x03},{0x3718, 0x10},{0x3719, 0x0c},{0x371a, 0x08},{0x371c, 0xfc},{0x3748, 0x00},{0x3760, 0x13},{0x3761, 0x33},{0x3762, 0x86},{0x3763, 0x16},{0x3767, 0x24},{0x3768, 0x06},{0x3769, 0x45},{0x376c, 0x23},{0x376f, 0x80},{0x3773, 0x06},{0x3d84, 0x00},{0x3d85, 0x17},{0x3d8c, 0x73},{0x3d8d, 0xbf},{0x3800, 0x00},{0x3801, 0x08},{0x3802, 0x00},{0x3803, 0x04},{0x3804, 0x10},{0x3805, 0x97},{0x3806, 0x0c},{0x3807, 0x4b},{0x3808, 0x08},{0x3809, 0x40},{0x380a, 0x06},{0x380b, 0x20},{0x380c, 0x12},{0x380d, 0xc0},{0x380e, 0x06},{0x380f, 0x80},{0x3810, 0x00},{0x3811, 0x04},{0x3812, 0x00},{0x3813, 0x02},{0x3814, 0x31},{0x3815, 0x31},{0x3820, 0x02},{0x3821, 0x06},{0x3823, 0x00},{0x3826, 0x00},{0x3827, 0x02},{0x3834, 0x00},{0x3835, 0x1c},{0x3836, 0x08},{0x3837, 0x02},{0x4000, 0xf1},{0x4001, 0x00},{0x4006, 0x04},{0x4007, 0x04},{0x400b, 0x0c},{0x4011, 0x00},{0x401a, 0x00},{0x401b, 0x00},{0x401c, 0x00},{0x401d, 0x00},{0x4020, 0x00},{0x4021, 0xe4},{0x4022, 0x04},{0x4023, 0xd7},{0x4024, 0x05},{0x4025, 0xbc},{0x4026, 0x05},{0x4027, 0xbf},{0x4028, 0x00},{0x4029, 0x02},{0x402a, 0x04},{0x402b, 0x08},{0x402c, 0x02},{0x402d, 0x02},{0x402e, 0x0c},{0x402f, 0x08},{0x403d, 0x2c},{0x403f, 0x7f},{0x4041, 0x07},{0x4500, 0x82},{0x4501, 0x3c},{0x458b, 0x00},{0x459c, 0x00},{0x459d, 0x00},{0x459e, 0x00},{0x4601, 0x83},{0x4602, 0x22},{0x4603, 0x01},{0x4800, 0x24}, //MIPI CLK control{0x4837, 0x19},{0x4d00, 0x04},{0x4d01, 0x42},{0x4d02, 0xd1},{0x4d03, 0x90},{0x4d04, 0x66},{0x4d05, 0x65},{0x4d0b, 0x00},{0x5000, 0x0e},{0x5001, 0x01},{0x5002, 0x07},{0x5013, 0x40},{0x501c, 0x00},{0x501d, 0x10},{0x510f, 0xfc},{0x5110, 0xf0},{0x5111, 0x10},{0x536d, 0x02},{0x536e, 0x67},{0x536f, 0x01},{0x5370, 0x4c},{0x5400, 0x00},{0x5400, 0x00},{0x5401, 0x61},{0x5402, 0x00},{0x5403, 0x00},{0x5404, 0x00},{0x5405, 0x40},{0x540c, 0x05},{0x5501, 0x00},{0x5b00, 0x00},{0x5b01, 0x00},{0x5b02, 0x01},{0x5b03, 0xff},{0x5b04, 0x02},{0x5b05, 0x6c},{0x5b09, 0x02},{0x5e00, 0x00},{0x5e10, 0x1c},{0x0102, 0x01}, //Fast standby enable{REG_NULL, 0x00},
};/** Xclk 24Mhz* max_framerate 30fps* mipi_datarate per lane 600Mbps*/
static const struct regval ov13850_2112x1568_regs[] = {{0x3612, 0x27},{0x370a, 0x26},{0x372a, 0x00},{0x372f, 0x90},{0x3801, 0x08},{0x3805, 0x97},{0x3807, 0x4b},{0x3808, 0x08},{0x3809, 0x40},{0x380a, 0x06},{0x380b, 0x20},{0x380c, 0x12},{0x380d, 0xc0},{0x380e, 0x06},{0x380f, 0x80},{0x3813, 0x02},{0x3814, 0x31},{0x3815, 0x31},{0x3820, 0x02},{0x3821, 0x05},{0x3836, 0x08},{0x3837, 0x02},{0x4601, 0x04},{0x4603, 0x00},{0x4020, 0x00},{0x4021, 0xE4},{0x4022, 0x07},{0x4023, 0x5F},{0x4024, 0x08},{0x4025, 0x44},{0x4026, 0x08},{0x4027, 0x47},{0x4603, 0x01},{0x5401, 0x61},{0x5405, 0x40},{REG_NULL, 0x00},
};/** Xclk 24Mhz* max_framerate 7fps* mipi_datarate per lane 600Mbps*/
static const struct regval ov13850_4224x3136_regs[] = {{0x3612, 0x2f},{0x370a, 0x24},{0x372a, 0x04},{0x372f, 0xa0},{0x3801, 0x0C},{0x3805, 0x93},{0x3807, 0x4B},{0x3808, 0x10},{0x3809, 0x80},{0x380a, 0x0c},{0x380b, 0x40},{0x380e, 0x0d},{0x380f, 0x00},{0x3813, 0x04},{0x3814, 0x11},{0x3815, 0x11},{0x3820, 0x00},{0x3821, 0x04},{0x3836, 0x04},{0x3837, 0x01},{0x4601, 0x87},{0x4603, 0x01},{0x4020, 0x02},{0x4021, 0x4C},{0x4022, 0x0E},{0x4023, 0x37},{0x4024, 0x0F},{0x4025, 0x1C},{0x4026, 0x0F},{0x4027, 0x1F},{0x4603, 0x00},{0x5401, 0x71},{0x5405, 0x80},{REG_NULL, 0x00},
};static const struct ov13850_mode supported_modes[] = {{.bus_fmt = MEDIA_BUS_FMT_SBGGR10_1X10,.width = 2112,.height = 1568,.max_fps = {.numerator = 10000,.denominator = 300000,},.exp_def = 0x0600,.hts_def = 0x12c0,.vts_def = 0x0680,.reg_list = ov13850_2112x1568_regs,.link_freq_idx = 0,.bpp = 10,},{.bus_fmt = MEDIA_BUS_FMT_SBGGR10_1X10,.width = 4224,.height = 3136,.max_fps = {.numerator = 20000,.denominator = 150000,},.exp_def = 0x0600,.hts_def = 0x12c0,.vts_def = 0x0d00,.reg_list = ov13850_4224x3136_regs,.link_freq_idx = 0,.bpp = 10,},
};static const u32 bus_code[] = {MEDIA_BUS_FMT_SBGGR10_1X10,
};static const s64 link_freq_menu_items[] = {OV13850_LINK_FREQ_300MHZ
};static const char * const ov13850_test_pattern_menu[] = {"Disabled","Vertical Color Bar Type 1","Vertical Color Bar Type 2","Vertical Color Bar Type 3","Vertical Color Bar Type 4"
};/* Write registers up to 4 at a time */
static int ov13850_write_reg(struct i2c_client *client, u16 reg,u32 len, u32 val)
{u32 buf_i, val_i;u8 buf[6];u8 *val_p;__be32 val_be;dev_dbg(&client->dev, "write reg(0x%x val:0x%x)!\n", reg, val);if (len > 4)return -EINVAL;buf[0] = reg >> 8;buf[1] = reg & 0xff;val_be = cpu_to_be32(val);val_p = (u8 *)&val_be;buf_i = 2;val_i = 4 - len;while (val_i < 4)buf[buf_i++] = val_p[val_i++];if (i2c_master_send(client, buf, len + 2) != len + 2)return -EIO;return 0;
}static int ov13850_write_array(struct i2c_client *client,const struct regval *regs)
{u32 i;int ret = 0;for (i = 0; ret == 0 && regs[i].addr != REG_NULL; i++)ret = ov13850_write_reg(client, regs[i].addr,OV13850_REG_VALUE_08BIT,regs[i].val);return ret;
}/* Read registers up to 4 at a time */
static int ov13850_read_reg(struct i2c_client *client, u16 reg,unsigned int len, u32 *val)
{struct i2c_msg msgs[2];u8 *data_be_p;__be32 data_be = 0;__be16 reg_addr_be = cpu_to_be16(reg);int ret;if (len > 4 || !len)return -EINVAL;data_be_p = (u8 *)&data_be;/* Write register address */msgs[0].addr = client->addr;msgs[0].flags = 0;msgs[0].len = 2;msgs[0].buf = (u8 *)&reg_addr_be;/* Read data from register */msgs[1].addr = client->addr;msgs[1].flags = I2C_M_RD;msgs[1].len = len;msgs[1].buf = &data_be_p[4 - len];ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));if (ret != ARRAY_SIZE(msgs))return -EIO;*val = be32_to_cpu(data_be);return 0;
}static int ov13850_get_reso_dist(const struct ov13850_mode *mode,struct v4l2_mbus_framefmt *framefmt)
{return abs(mode->width - framefmt->width) +abs(mode->height - framefmt->height);
}static const struct ov13850_mode *
ov13850_find_best_fit(struct v4l2_subdev_format *fmt)
{struct v4l2_mbus_framefmt *framefmt = &fmt->format;int dist;int cur_best_fit = 0;int cur_best_fit_dist = -1;unsigned int i;for (i = 0; i < ARRAY_SIZE(supported_modes); i++) {dist = ov13850_get_reso_dist(&supported_modes[i], framefmt);if (cur_best_fit_dist == -1 || dist < cur_best_fit_dist) {cur_best_fit_dist = dist;cur_best_fit = i;}}return &supported_modes[cur_best_fit];
}static int ov13850_set_fmt(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg,struct v4l2_subdev_format *fmt)
{struct ov13850 *ov13850 = to_ov13850(sd);const struct ov13850_mode *mode;s64 h_blank, vblank_def;mutex_lock(&ov13850->mutex);mode = ov13850_find_best_fit(fmt);fmt->format.code = mode->bus_fmt;fmt->format.width = mode->width;fmt->format.height = mode->height;fmt->format.field = V4L2_FIELD_NONE;if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API*v4l2_subdev_get_try_format(sd, cfg, fmt->pad) = fmt->format;
#elsemutex_unlock(&ov13850->mutex);return -ENOTTY;
#endif} else {ov13850->cur_mode = mode;h_blank = mode->hts_def - mode->width;__v4l2_ctrl_modify_range(ov13850->hblank, h_blank,h_blank, 1, h_blank);vblank_def = mode->vts_def - mode->height;__v4l2_ctrl_modify_range(ov13850->vblank, vblank_def,OV13850_VTS_MAX - mode->height,1, vblank_def);ov13850->cur_fps = mode->max_fps;}mutex_unlock(&ov13850->mutex);return 0;
}static int ov13850_get_fmt(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg,struct v4l2_subdev_format *fmt)
{struct ov13850 *ov13850 = to_ov13850(sd);const struct ov13850_mode *mode = ov13850->cur_mode;mutex_lock(&ov13850->mutex);if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
#ifdef CONFIG_VIDEO_V4L2_SUBDEV_APIfmt->format = *v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
#elsemutex_unlock(&ov13850->mutex);return -ENOTTY;
#endif} else {fmt->format.width = mode->width;fmt->format.height = mode->height;fmt->format.code = mode->bus_fmt;fmt->format.field = V4L2_FIELD_NONE;}mutex_unlock(&ov13850->mutex);return 0;
}static int ov13850_enum_mbus_code(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg,struct v4l2_subdev_mbus_code_enum *code)
{if (code->index >= ARRAY_SIZE(bus_code))return -EINVAL;code->code = bus_code[code->index];return 0;
}static int ov13850_enum_frame_sizes(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg,struct v4l2_subdev_frame_size_enum *fse)
{if (fse->index >= ARRAY_SIZE(supported_modes))return -EINVAL;if (fse->code != supported_modes[fse->index].bus_fmt)return -EINVAL;fse->min_width  = supported_modes[fse->index].width;fse->max_width  = supported_modes[fse->index].width;fse->max_height = supported_modes[fse->index].height;fse->min_height = supported_modes[fse->index].height;return 0;
}static int ov13850_enable_test_pattern(struct ov13850 *ov13850, u32 pattern)
{u32 val;if (pattern)val = (pattern - 1) | OV13850_TEST_PATTERN_ENABLE;elseval = OV13850_TEST_PATTERN_DISABLE;return ov13850_write_reg(ov13850->client,OV13850_REG_TEST_PATTERN,OV13850_REG_VALUE_08BIT,val);
}static int ov13850_g_frame_interval(struct v4l2_subdev *sd,struct v4l2_subdev_frame_interval *fi)
{struct ov13850 *ov13850 = to_ov13850(sd);const struct ov13850_mode *mode = ov13850->cur_mode;if (ov13850->streaming)fi->interval = ov13850->cur_fps;elsefi->interval = mode->max_fps;return 0;
}static const struct ov13850_mode *ov13850_find_mode(struct ov13850 *ov13850, int fps)
{const struct ov13850_mode *mode = NULL;const struct ov13850_mode *match = NULL;int cur_fps = 0;int i = 0;for (i = 0; i < ARRAY_SIZE(supported_modes); i++) {mode = &supported_modes[i];if (mode->width == ov13850->cur_mode->width &&mode->height == ov13850->cur_mode->height) {cur_fps = DIV_ROUND_CLOSEST(mode->max_fps.denominator, mode->max_fps.numerator);if (cur_fps == fps) {match = mode;break;}}}return match;
}static int ov13850_s_frame_interval(struct v4l2_subdev *sd,struct v4l2_subdev_frame_interval *fi)
{struct ov13850 *ov13850 = to_ov13850(sd);const struct ov13850_mode *mode = NULL;struct v4l2_fract *fract = &fi->interval;s64 h_blank, vblank_def;u64 pixel_rate = 0;u32 lane_num = OV13850_LANES;int fps;if (ov13850->streaming)return -EBUSY;if (fi->pad != 0)return -EINVAL;if (fract->numerator == 0) {v4l2_err(sd, "error param, check interval param\n");return -EINVAL;}fps = DIV_ROUND_CLOSEST(fract->denominator, fract->numerator);mode = ov13850_find_mode(ov13850, fps);if (mode == NULL) {v4l2_err(sd, "couldn't match fi\n");return -EINVAL;}ov13850->cur_mode = mode;h_blank = mode->hts_def - mode->width;__v4l2_ctrl_modify_range(ov13850->hblank, h_blank,h_blank, 1, h_blank);vblank_def = mode->vts_def - mode->height;__v4l2_ctrl_modify_range(ov13850->vblank, vblank_def,OV13850_VTS_MAX - mode->height,1, vblank_def);pixel_rate = (u32)link_freq_menu_items[mode->link_freq_idx] / mode->bpp * 2 * lane_num;__v4l2_ctrl_s_ctrl_int64(ov13850->pixel_rate,pixel_rate);__v4l2_ctrl_s_ctrl(ov13850->link_freq,mode->link_freq_idx);ov13850->cur_fps = mode->max_fps;return 0;
}static void ov13850_get_module_inf(struct ov13850 *ov13850,struct rkmodule_inf *inf)
{memset(inf, 0, sizeof(*inf));strlcpy(inf->base.sensor, OV13850_NAME, sizeof(inf->base.sensor));strlcpy(inf->base.module, ov13850->module_name,sizeof(inf->base.module));strlcpy(inf->base.lens, ov13850->len_name, sizeof(inf->base.lens));
}static long ov13850_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg)
{struct ov13850 *ov13850 = to_ov13850(sd);long ret = 0;u32 stream = 0;switch (cmd) {case RKMODULE_GET_MODULE_INFO:ov13850_get_module_inf(ov13850, (struct rkmodule_inf *)arg);break;case RKMODULE_SET_QUICK_STREAM:stream = *((u32 *)arg);if (stream)ret = ov13850_write_reg(ov13850->client,OV13850_REG_CTRL_MODE,OV13850_REG_VALUE_08BIT,OV13850_MODE_STREAMING);elseret = ov13850_write_reg(ov13850->client,OV13850_REG_CTRL_MODE,OV13850_REG_VALUE_08BIT,OV13850_MODE_SW_STANDBY);break;default:ret = -ENOIOCTLCMD;break;}return ret;
}#ifdef CONFIG_COMPAT
static long ov13850_compat_ioctl32(struct v4l2_subdev *sd,unsigned int cmd, unsigned long arg)
{void __user *up = compat_ptr(arg);struct rkmodule_inf *inf;struct rkmodule_awb_cfg *cfg;long ret;u32 stream = 0;switch (cmd) {case RKMODULE_GET_MODULE_INFO:inf = kzalloc(sizeof(*inf), GFP_KERNEL);if (!inf) {ret = -ENOMEM;return ret;}ret = ov13850_ioctl(sd, cmd, inf);if (!ret)ret = copy_to_user(up, inf, sizeof(*inf));kfree(inf);break;case RKMODULE_AWB_CFG:cfg = kzalloc(sizeof(*cfg), GFP_KERNEL);if (!cfg) {ret = -ENOMEM;return ret;}ret = copy_from_user(cfg, up, sizeof(*cfg));if (!ret)ret = ov13850_ioctl(sd, cmd, cfg);kfree(cfg);break;case RKMODULE_SET_QUICK_STREAM:ret = copy_from_user(&stream, up, sizeof(u32));if (!ret)ret = ov13850_ioctl(sd, cmd, &stream);break;default:ret = -ENOIOCTLCMD;break;}return ret;
}
#endifstatic int __ov13850_start_stream(struct ov13850 *ov13850)
{int ret;ret = ov13850_write_array(ov13850->client, ov13850->cur_mode->reg_list);if (ret)return ret;/* In case these controls are set before streaming */mutex_unlock(&ov13850->mutex);ret = v4l2_ctrl_handler_setup(&ov13850->ctrl_handler);mutex_lock(&ov13850->mutex);if (ret)return ret;return ov13850_write_reg(ov13850->client,OV13850_REG_CTRL_MODE,OV13850_REG_VALUE_08BIT,OV13850_MODE_STREAMING);
}static int __ov13850_stop_stream(struct ov13850 *ov13850)
{return ov13850_write_reg(ov13850->client,OV13850_REG_CTRL_MODE,OV13850_REG_VALUE_08BIT,OV13850_MODE_SW_STANDBY);
}static int ov13850_s_stream(struct v4l2_subdev *sd, int on)
{struct ov13850 *ov13850 = to_ov13850(sd);struct i2c_client *client = ov13850->client;int ret = 0;mutex_lock(&ov13850->mutex);on = !!on;if (on == ov13850->streaming)goto unlock_and_return;if (on) {ret = pm_runtime_get_sync(&client->dev);if (ret < 0) {pm_runtime_put_noidle(&client->dev);goto unlock_and_return;}ret = __ov13850_start_stream(ov13850);if (ret) {v4l2_err(sd, "start stream failed while write regs\n");pm_runtime_put(&client->dev);goto unlock_and_return;}} else {__ov13850_stop_stream(ov13850);pm_runtime_put(&client->dev);}ov13850->streaming = on;unlock_and_return:mutex_unlock(&ov13850->mutex);return ret;
}static int ov13850_s_power(struct v4l2_subdev *sd, int on)
{struct ov13850 *ov13850 = to_ov13850(sd);struct i2c_client *client = ov13850->client;int ret = 0;mutex_lock(&ov13850->mutex);/* If the power state is not modified - no work to do. */if (ov13850->power_on == !!on)goto unlock_and_return;if (on) {ret = pm_runtime_get_sync(&client->dev);if (ret < 0) {pm_runtime_put_noidle(&client->dev);goto unlock_and_return;}ret = ov13850_write_array(ov13850->client, ov13850_global_regs);if (ret) {v4l2_err(sd, "could not set init registers\n");pm_runtime_put_noidle(&client->dev);goto unlock_and_return;}ov13850->power_on = true;} else {pm_runtime_put(&client->dev);ov13850->power_on = false;}unlock_and_return:mutex_unlock(&ov13850->mutex);return ret;
}/* Calculate the delay in us by clock rate and clock cycles */
static inline u32 ov13850_cal_delay(u32 cycles)
{return DIV_ROUND_UP(cycles, OV13850_XVCLK_FREQ / 1000 / 1000);
}static int __ov13850_power_on(struct ov13850 *ov13850)
{int ret;u32 delay_us;struct device *dev = &ov13850->client->dev;if (!IS_ERR(ov13850->power_gpio))gpiod_set_value_cansleep(ov13850->power_gpio, 1);usleep_range(1000, 2000);if (!IS_ERR_OR_NULL(ov13850->pins_default)) {ret = pinctrl_select_state(ov13850->pinctrl,ov13850->pins_default);if (ret < 0)dev_err(dev, "could not set pins\n");}ret = clk_set_rate(ov13850->xvclk, OV13850_XVCLK_FREQ);if (ret < 0)dev_warn(dev, "Failed to set xvclk rate (24MHz)\n");if (clk_get_rate(ov13850->xvclk) != OV13850_XVCLK_FREQ)dev_warn(dev, "xvclk mismatched, modes are based on 24MHz\n");ret = clk_prepare_enable(ov13850->xvclk);if (ret < 0) {dev_err(dev, "Failed to enable xvclk\n");return ret;}if (!IS_ERR(ov13850->reset_gpio))gpiod_set_value_cansleep(ov13850->reset_gpio, 0);ret = regulator_bulk_enable(OV13850_NUM_SUPPLIES, ov13850->supplies);if (ret < 0) {dev_err(dev, "Failed to enable regulators\n");goto disable_clk;}if (!IS_ERR(ov13850->reset_gpio))gpiod_set_value_cansleep(ov13850->reset_gpio, 1);usleep_range(500, 1000);if (!IS_ERR(ov13850->pwdn_gpio))gpiod_set_value_cansleep(ov13850->pwdn_gpio, 1);/* 8192 cycles prior to first SCCB transaction */delay_us = ov13850_cal_delay(8192);usleep_range(delay_us, delay_us * 2);return 0;disable_clk:clk_disable_unprepare(ov13850->xvclk);return ret;
}static void __ov13850_power_off(struct ov13850 *ov13850)
{int ret;struct device *dev = &ov13850->client->dev;if (!IS_ERR(ov13850->pwdn_gpio))gpiod_set_value_cansleep(ov13850->pwdn_gpio, 0);clk_disable_unprepare(ov13850->xvclk);if (!IS_ERR(ov13850->reset_gpio))gpiod_set_value_cansleep(ov13850->reset_gpio, 0);if (!IS_ERR_OR_NULL(ov13850->pins_sleep)) {ret = pinctrl_select_state(ov13850->pinctrl,ov13850->pins_sleep);if (ret < 0)dev_dbg(dev, "could not set pins\n");}if (!IS_ERR(ov13850->power_gpio))gpiod_set_value_cansleep(ov13850->power_gpio, 0);regulator_bulk_disable(OV13850_NUM_SUPPLIES, ov13850->supplies);
}static int __maybe_unused ov13850_runtime_resume(struct device *dev)
{struct i2c_client *client = to_i2c_client(dev);struct v4l2_subdev *sd = i2c_get_clientdata(client);struct ov13850 *ov13850 = to_ov13850(sd);return __ov13850_power_on(ov13850);
}static int __maybe_unused ov13850_runtime_suspend(struct device *dev)
{struct i2c_client *client = to_i2c_client(dev);struct v4l2_subdev *sd = i2c_get_clientdata(client);struct ov13850 *ov13850 = to_ov13850(sd);__ov13850_power_off(ov13850);return 0;
}#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
static int ov13850_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
{struct ov13850 *ov13850 = to_ov13850(sd);struct v4l2_mbus_framefmt *try_fmt =v4l2_subdev_get_try_format(sd, fh->pad, 0);const struct ov13850_mode *def_mode = &supported_modes[0];mutex_lock(&ov13850->mutex);/* Initialize try_fmt */try_fmt->width = def_mode->width;try_fmt->height = def_mode->height;try_fmt->code = def_mode->bus_fmt;try_fmt->field = V4L2_FIELD_NONE;mutex_unlock(&ov13850->mutex);/* No crop or compose */return 0;
}
#endifstatic int ov13850_enum_frame_interval(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg,struct v4l2_subdev_frame_interval_enum *fie)
{if (fie->index >= ARRAY_SIZE(supported_modes))return -EINVAL;fie->code = supported_modes[fie->index].bus_fmt;fie->width = supported_modes[fie->index].width;fie->height = supported_modes[fie->index].height;fie->interval = supported_modes[fie->index].max_fps;return 0;
}static int ov13850_g_mbus_config(struct v4l2_subdev *sd, unsigned int pad_id,struct v4l2_mbus_config *config)
{u32 val = 0;val = 1 << (OV13850_LANES - 1) |V4L2_MBUS_CSI2_CHANNEL_0 |V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;config->type = V4L2_MBUS_CSI2_DPHY;config->flags = val;return 0;
}static const struct dev_pm_ops ov13850_pm_ops = {SET_RUNTIME_PM_OPS(ov13850_runtime_suspend,ov13850_runtime_resume, NULL)
};#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API
static const struct v4l2_subdev_internal_ops ov13850_internal_ops = {.open = ov13850_open,
};
#endifstatic const struct v4l2_subdev_core_ops ov13850_core_ops = {.s_power = ov13850_s_power,.ioctl = ov13850_ioctl,
#ifdef CONFIG_COMPAT.compat_ioctl32 = ov13850_compat_ioctl32,
#endif
};static const struct v4l2_subdev_video_ops ov13850_video_ops = {.s_stream = ov13850_s_stream,.g_frame_interval = ov13850_g_frame_interval,.s_frame_interval = ov13850_s_frame_interval,
};static const struct v4l2_subdev_pad_ops ov13850_pad_ops = {.enum_mbus_code = ov13850_enum_mbus_code,.enum_frame_size = ov13850_enum_frame_sizes,.enum_frame_interval = ov13850_enum_frame_interval,.get_fmt = ov13850_get_fmt,.set_fmt = ov13850_set_fmt,.get_mbus_config = ov13850_g_mbus_config,
};static const struct v4l2_subdev_ops ov13850_subdev_ops = {.core	= &ov13850_core_ops,.video	= &ov13850_video_ops,.pad	= &ov13850_pad_ops,
};static void ov13850_modify_fps_info(struct ov13850 *ov13850)
{const struct ov13850_mode *mode = ov13850->cur_mode;ov13850->cur_fps.denominator = mode->max_fps.denominator * mode->vts_def /ov13850->cur_vts;
}static int ov13850_set_ctrl(struct v4l2_ctrl *ctrl)
{struct ov13850 *ov13850 = container_of(ctrl->handler,struct ov13850, ctrl_handler);struct i2c_client *client = ov13850->client;s64 max;int ret = 0;/* Propagate change of current control to all related controls */switch (ctrl->id) {case V4L2_CID_VBLANK:/* Update max exposure while meeting expected vblanking */max = ov13850->cur_mode->height + ctrl->val - 16;__v4l2_ctrl_modify_range(ov13850->exposure,ov13850->exposure->minimum, max,ov13850->exposure->step,ov13850->exposure->default_value);break;}if (!pm_runtime_get_if_in_use(&client->dev))return 0;switch (ctrl->id) {case V4L2_CID_EXPOSURE:/* 4 least significant bits of expsoure are fractional part */ret = ov13850_write_reg(ov13850->client,OV13850_REG_EXPOSURE,OV13850_REG_VALUE_24BIT,ctrl->val << 4);break;case V4L2_CID_ANALOGUE_GAIN:ret = ov13850_write_reg(ov13850->client,OV13850_REG_GAIN_H,OV13850_REG_VALUE_08BIT,(ctrl->val >> OV13850_GAIN_H_SHIFT) &OV13850_GAIN_H_MASK);ret |= ov13850_write_reg(ov13850->client,OV13850_REG_GAIN_L,OV13850_REG_VALUE_08BIT,ctrl->val & OV13850_GAIN_L_MASK);break;case V4L2_CID_VBLANK:ret = ov13850_write_reg(ov13850->client,OV13850_REG_VTS,OV13850_REG_VALUE_16BIT,ctrl->val + ov13850->cur_mode->height);ov13850->cur_vts = ctrl->val + ov13850->cur_mode->height;ov13850_modify_fps_info(ov13850);break;case V4L2_CID_TEST_PATTERN:ret = ov13850_enable_test_pattern(ov13850, ctrl->val);break;default:dev_warn(&client->dev, "%s Unhandled id:0x%x, val:0x%x\n",__func__, ctrl->id, ctrl->val);break;}pm_runtime_put(&client->dev);return ret;
}static const struct v4l2_ctrl_ops ov13850_ctrl_ops = {.s_ctrl = ov13850_set_ctrl,
};static int ov13850_initialize_controls(struct ov13850 *ov13850)
{const struct ov13850_mode *mode;struct v4l2_ctrl_handler *handler;s64 exposure_max, vblank_def;u32 h_blank;int ret;handler = &ov13850->ctrl_handler;mode = ov13850->cur_mode;ret = v4l2_ctrl_handler_init(handler, 8);if (ret)return ret;handler->lock = &ov13850->mutex;ov13850->link_freq = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,0, 0, link_freq_menu_items);if (ov13850->link_freq)ov13850->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;ov13850->pixel_rate = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,0, OV13850_PIXEL_RATE, 1, OV13850_PIXEL_RATE);h_blank = mode->hts_def - mode->width;ov13850->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,h_blank, h_blank, 1, h_blank);if (ov13850->hblank)ov13850->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;vblank_def = mode->vts_def - mode->height;ov13850->vblank = v4l2_ctrl_new_std(handler, &ov13850_ctrl_ops,V4L2_CID_VBLANK, vblank_def,OV13850_VTS_MAX - mode->height,1, vblank_def);exposure_max = mode->vts_def - 16;ov13850->exposure = v4l2_ctrl_new_std(handler, &ov13850_ctrl_ops,V4L2_CID_EXPOSURE, OV13850_EXPOSURE_MIN,exposure_max, OV13850_EXPOSURE_STEP,mode->exp_def);ov13850->anal_gain = v4l2_ctrl_new_std(handler, &ov13850_ctrl_ops,V4L2_CID_ANALOGUE_GAIN, OV13850_GAIN_MIN,OV13850_GAIN_MAX, OV13850_GAIN_STEP,OV13850_GAIN_DEFAULT);ov13850->test_pattern = v4l2_ctrl_new_std_menu_items(handler,&ov13850_ctrl_ops, V4L2_CID_TEST_PATTERN,ARRAY_SIZE(ov13850_test_pattern_menu) - 1,0, 0, ov13850_test_pattern_menu);if (handler->error) {ret = handler->error;dev_err(&ov13850->client->dev,"Failed to init controls(%d)\n", ret);goto err_free_handler;}ov13850->subdev.ctrl_handler = handler;return 0;err_free_handler:v4l2_ctrl_handler_free(handler);return ret;
}static int ov13850_check_sensor_id(struct ov13850 *ov13850,struct i2c_client *client)
{struct device *dev = &ov13850->client->dev;u32 id = 0;int ret;ret = ov13850_read_reg(client, OV13850_REG_CHIP_ID,OV13850_REG_VALUE_16BIT, &id);if (id != CHIP_ID) {dev_err(dev, "Unexpected sensor id(%06x), ret(%d)\n", id, ret);return -ENODEV;}ret = ov13850_read_reg(client, OV13850_CHIP_REVISION_REG,OV13850_REG_VALUE_08BIT, &id);if (ret) {dev_err(dev, "Read chip revision register error\n");return ret;}if (id == OV13850_R2A)ov13850_global_regs = ov13850_global_regs_r2a;elseov13850_global_regs = ov13850_global_regs_r1a;dev_info(dev, "Detected OV%06x sensor, REVISION 0x%x\n", CHIP_ID, id);return 0;
}static int ov13850_configure_regulators(struct ov13850 *ov13850)
{unsigned int i;for (i = 0; i < OV13850_NUM_SUPPLIES; i++)ov13850->supplies[i].supply = ov13850_supply_names[i];return devm_regulator_bulk_get(&ov13850->client->dev,OV13850_NUM_SUPPLIES,ov13850->supplies);
}static int ov13850_probe(struct i2c_client *client,const struct i2c_device_id *id)
{struct device *dev = &client->dev;struct device_node *node = dev->of_node;struct ov13850 *ov13850;struct v4l2_subdev *sd;char facing[2];int ret;dev_info(dev, "driver version: %02x.%02x.%02x",DRIVER_VERSION >> 16,(DRIVER_VERSION & 0xff00) >> 8,DRIVER_VERSION & 0x00ff);ov13850 = devm_kzalloc(dev, sizeof(*ov13850), GFP_KERNEL);if (!ov13850)return -ENOMEM;ret = of_property_read_u32(node, RKMODULE_CAMERA_MODULE_INDEX,&ov13850->module_index);ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_FACING,&ov13850->module_facing);ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_NAME,&ov13850->module_name);ret |= of_property_read_string(node, RKMODULE_CAMERA_LENS_NAME,&ov13850->len_name);if (ret) {dev_err(dev, "could not get module information!\n");return -EINVAL;}ov13850->client = client;ov13850->cur_mode = &supported_modes[0];ov13850->xvclk = devm_clk_get(dev, "xvclk");if (IS_ERR(ov13850->xvclk)) {dev_err(dev, "Failed to get xvclk\n");return -EINVAL;}ov13850->power_gpio = devm_gpiod_get(dev, "power", GPIOD_OUT_LOW);if (IS_ERR(ov13850->power_gpio))dev_warn(dev, "Failed to get power-gpios, maybe no use\n");ov13850->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);if (IS_ERR(ov13850->reset_gpio))dev_warn(dev, "Failed to get reset-gpios\n");ov13850->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW);if (IS_ERR(ov13850->pwdn_gpio))dev_warn(dev, "Failed to get pwdn-gpios\n");ret = ov13850_configure_regulators(ov13850);if (ret) {dev_err(dev, "Failed to get power regulators\n");return ret;}ov13850->pinctrl = devm_pinctrl_get(dev);if (!IS_ERR(ov13850->pinctrl)) {ov13850->pins_default =pinctrl_lookup_state(ov13850->pinctrl,OF_CAMERA_PINCTRL_STATE_DEFAULT);if (IS_ERR(ov13850->pins_default))dev_err(dev, "could not get default pinstate\n");ov13850->pins_sleep =pinctrl_lookup_state(ov13850->pinctrl,OF_CAMERA_PINCTRL_STATE_SLEEP);if (IS_ERR(ov13850->pins_sleep))dev_err(dev, "could not get sleep pinstate\n");}mutex_init(&ov13850->mutex);sd = &ov13850->subdev;v4l2_i2c_subdev_init(sd, client, &ov13850_subdev_ops);ret = ov13850_initialize_controls(ov13850);if (ret)goto err_destroy_mutex;ret = __ov13850_power_on(ov13850);if (ret)goto err_free_handler;ret = ov13850_check_sensor_id(ov13850, client);if (ret)goto err_power_off;#ifdef CONFIG_VIDEO_V4L2_SUBDEV_APIsd->internal_ops = &ov13850_internal_ops;sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
#endif
#if defined(CONFIG_MEDIA_CONTROLLER)ov13850->pad.flags = MEDIA_PAD_FL_SOURCE;sd->entity.function = MEDIA_ENT_F_CAM_SENSOR;ret = media_entity_pads_init(&sd->entity, 1, &ov13850->pad);if (ret < 0)goto err_power_off;
#endifmemset(facing, 0, sizeof(facing));if (strcmp(ov13850->module_facing, "back") == 0)facing[0] = 'b';elsefacing[0] = 'f';snprintf(sd->name, sizeof(sd->name), "m%02d_%s_%s %s",ov13850->module_index, facing,OV13850_NAME, dev_name(sd->dev));ret = v4l2_async_register_subdev_sensor_common(sd);if (ret) {dev_err(dev, "v4l2 async register subdev failed\n");goto err_clean_entity;}pm_runtime_set_active(dev);pm_runtime_enable(dev);pm_runtime_idle(dev);return 0;err_clean_entity:
#if defined(CONFIG_MEDIA_CONTROLLER)media_entity_cleanup(&sd->entity);
#endif
err_power_off:__ov13850_power_off(ov13850);
err_free_handler:v4l2_ctrl_handler_free(&ov13850->ctrl_handler);
err_destroy_mutex:mutex_destroy(&ov13850->mutex);return ret;
}static int ov13850_remove(struct i2c_client *client)
{struct v4l2_subdev *sd = i2c_get_clientdata(client);struct ov13850 *ov13850 = to_ov13850(sd);v4l2_async_unregister_subdev(sd);
#if defined(CONFIG_MEDIA_CONTROLLER)media_entity_cleanup(&sd->entity);
#endifv4l2_ctrl_handler_free(&ov13850->ctrl_handler);mutex_destroy(&ov13850->mutex);pm_runtime_disable(&client->dev);if (!pm_runtime_status_suspended(&client->dev))__ov13850_power_off(ov13850);pm_runtime_set_suspended(&client->dev);return 0;
}#if IS_ENABLED(CONFIG_OF)
static const struct of_device_id ov13850_of_match[] = {{ .compatible = "ovti,ov13850" },{},
};
MODULE_DEVICE_TABLE(of, ov13850_of_match);
#endifstatic const struct i2c_device_id ov13850_match_id[] = {{ "ovti,ov13850", 0 },{ },
};static struct i2c_driver ov13850_i2c_driver = {.driver = {.name = OV13850_NAME,.pm = &ov13850_pm_ops,.of_match_table = of_match_ptr(ov13850_of_match),},.probe		= &ov13850_probe,.remove		= &ov13850_remove,.id_table	= ov13850_match_id,
};static int __init sensor_mod_init(void)
{return i2c_add_driver(&ov13850_i2c_driver);
}static void __exit sensor_mod_exit(void)
{i2c_del_driver(&ov13850_i2c_driver);
}device_initcall_sync(sensor_mod_init);
module_exit(sensor_mod_exit);MODULE_DESCRIPTION("OmniVision ov13850 sensor driver");
MODULE_LICENSE("GPL v2");

【源码分析】Linux内核ov13850.c

这里写自定义目录标题 1、入口函数：__init sensor_mod_init2、probe函数：ov13850_probe2.1、初始化前的一些准备2.2、设备初始化流程源码如下了解运行流程 1、入口函数：__init sensor_mod_init 驱动由 __init 开始 __exit 结束&#xff0c…...

编程日记 2025/7/13 1:30:52

单片机与FPGA的核心差异、优缺点、编程差异、典型应用场景、选型等对比分析

1. 基本概念差异单片机（MCU）： 基于冯诺依曼/哈佛架构的微控制器，集成CPU、内存、外设接口（如ADC、UART、PWM等），通过软件指令顺序执行任务。 FPGA： 由可编程逻辑单元（…...

编程日记 2025/7/13 0:37:56

PCB规则

PCB封装原理图绘制完成需要检查 DRC 菜单栏——>设计——>检查 DRC 底部侧边栏——>DRC——>检查 DRC 常见问题： 1）某个导线/网络标签是一个单网络网络标签名称不一样网络标签只有一个引脚没有使用，但是放置了导线 2&#xf…...

编程日记 2025/7/13 1:03:56

静态存储区（Static Storage Area）的总结

普通的全局变量未初始化，编译阶段放在com段，链接完后放在bss段在32位系统中，内核空间为1GB（地址范围：0xC0000000-0xFFFFFFFF），用户空间为3GB 高端内存（HIGHMEM）是32位…...

编程日记 2025/7/12 11:24:52

基于Quill的文档编辑器开发日志（上）——前端核心功能实现与本地存储管理

目录二、技术选型与架构设计三、核心功能实现 1. Quill编辑器集成 2. 本地存储管理（DocStorage类） 3. 文档树渲染与事件绑定四、效果演示与问题总结一、项目背景在开发 Taskflow智能Todo系统的过程中，文档管理模块是核心功能之一…...

编程日记 2025/7/12 23:54:12

Java | 深拷贝与浅拷贝工具类解析和自定义实现

关注：CodingTechWork 引言在 Java 开发中，对象的拷贝是一个常见的需求，尤其是在处理复杂数据结构时。深拷贝（Deep Copy）和浅拷贝（Shallow Copy）是两种常见的拷贝方式，它们在实现和…...

编程日记 2025/7/13 0:31:04

《巧用DeepSeek快速搞定数据分析》书籍分享

文章目录前言内容简介作者简介购书链接书籍目录前言随着大数据时代的到来，数据分析和人工智能技术正迅速改变着各行各业的运作方式。DeepSeek作为先进的人工智能模型，不仅在自然语言处理领域具有广泛应用，还在数据分析、图像识别、推荐系…...

编程日记 2025/7/13 0:27:04

skynet.cluster 库函数应用

目录模块概览核心函数解析1. 节点通信2. 节点配置与监听3. 服务注册与查询4. 远程服务代理底层机制使用场景示例场景1：跨节点数据存储场景2：动态扩展节点注意事项以下是对 cluster.lua 模块的详细解析，涵盖其核心功能、函数用途及使用示例…...

编程日记 2025/7/13 0:19:05

精益数据分析（17/126）：精益画布与创业方向抉择

精益数据分析（17/126）：精益画布与创业方向抉择大家好！一直以来，我都希望能和大家一起在创业和数据分析的领域中不断探索、共同进步。今天，我们接着深入学习《精益数据分析》，这次聚焦于精益画…...

编程日记 2025/7/13 0:24:48

同样的接口用postman/apifox能跑通，用jmeter跑就报错500

之前没用过jmeter,第一次用调试压测脚本遇到了问题一样的接口用postman能跑通，用jmeter跑就报错500，百度很多文章都说是该接口需要加一个‘内容编码’改成utf-8,我加了还是不行后来我就想到apifox好像有隐藏的header，然后开始比较apifox的…...

编程日记 2025/7/13 0:02:03

编写 Markdown 技术文档示例

文章目录 📄 建议的文档命名规则（文件名）✍️ 如何署名与归属标识示例 OpenShift 安装部署前置条件说明文档说明使用说明 📄 建议的文档命名规则（文件名） OCP_Install_Prerequisites_Ghostwritten-v1.0-20…...

编程日记 2025/7/13 0:12:37

23种设计模式-结构型模式之享元模式（Java版本）

Java 享元模式（Flyweight Pattern）详解 🦋 什么是享元模式？ 享元模式是一种结构型模式，它通过共享相同的对象来减少内存消耗，适用于大量细粒度对象的场景。关键思想是缓存重复出现的对象，避免…...

编程日记 2025/7/12 7:06:28

单例模式：确保唯一实例的设计模式

单例模式：确保唯一实例的设计模式一、模式核心：保证类仅有一个实例并提供全局访问点在软件开发中，有些类需要确保只有一个实例（如系统配置类、日志管理器），避免因多个实例导致状态混乱或资源浪费。单…...

编程日记 2025/7/12 23:54:12

gem5-gpu教程04 高速缓存一致性协议和缓存拓扑

高速缓存一致性协议 gem5-gpu 的一大贡献是允许用户灵活地定义 GPU 和 GPU-CPU 间的缓存一致性协议。此功能由 gem5 的 Ruby 模块实现，该模块使用 SLICC 语言定义一致性协议。更多信息请访问 gem5 wiki：[[http://gem5.org/Ruby]]。缓存拓扑 The topology of the cache hi…...

编程日记 2025/7/13 0:32:30

c++ 互斥锁

为练习c 线程同步，做了LeeCode 1114题. 按序打印： 给你一个类： public class Foo {public void first() { print("first"); }public void second() { print("second"); }public void third() { print("third"…...

编程日记 2025/7/13 0:23:29

Pytest教程：为什么Pytest要用插件模式？

目录一、历史背景：测试框架的局限性与Pytest的设计哲学 1.1 早期测试框架的困境 1.2 Pytest的模块化设计二、横向对比：插件机制如何让Pytest脱颖而出 2.1 与Unittest/Nose的对比 2.2 插件模式的架构优势三、插件模式的核心优势解析 3.1 可扩展…...

编程日记 2025/7/13 0:52:55

JVM 生产环境问题定位与解决实战（七）：实战篇——OSSClient泄漏引发的FullGC风暴

本文已收录于《JVM生产环境问题定位与解决实战》专栏，完整系列见文末目录引言在前六篇博客中，我们系统性地学习了 JVM 生产环境问题定位与解决的全套工具链，涵盖jps、jmap、jstat、jstack、jcmd 等基础工具的使用技巧，深入剖析…...

编程日记 2025/7/12 23:52:40

缩放点积注意力

Scaled Dot-Product Attention 论文地址 https://arxiv.org/pdf/1706.03762 注意力机制介绍缩放点积注意力是Transformer模型的核心组件，用于计算序列中不同位置之间的关联程度。其核心思想是通过查询向量（query）和键向量（key&am…...

编程日记 2025/7/12 23:58:57

一个关于相对速度的假想的故事-7

回到， 它其实还可以写成， 也就是说，把作为1，它的倍也是存在和成立的。或者说，如果认为是某一种单位（虚数为单位），那么的平方显然也是一种单位（-1为单位&#xff09…...

编程日记 2025/7/10 14:14:34

LeetCode算法题(Go语言实现)_57

题目给定一个仅包含数字 2-9 的字符串，返回所有它能表示的字母组合。答案可以按任意顺序返回。给出数字到字母的映射如下（与电话按键相同）。注意 1 不对应任何字母。一、代码实现（回溯法） func letterCombinatio…...

编程日记 2025/6/29 11:47:04

从GPT-5到Claude 3：大模型竞赛的下一站是什么？

从GPT-5到Claude 3：大模型竞赛的下一站是什么？ 引言随着人工智能技术的飞速发展，大语言模型（LLM）已经成为推动自然语言处理（NLP）领域进步的关键力量。自2018年OpenAI推出GPT-1以来&#xff0…...

编程日记 2025/7/12 2:23:07

leetcode - 字符串

字符串 466. 统计重复个数题目定义 str [s, n] 表示 str 由 n 个字符串 s 连接构成。例如，str ["abc", 3] "abcabcabc" 。如果可以从 s2( )中删除某些字符使其变为 s1，则称字符串 s1( )可以从字符串 s2 获得。例如&#xf…...

编程日记 2025/7/10 19:44:40

运维打铁：网络基础知识

文章目录一、网络架构1. 网络架构图2. 各层级功能3. 机房网络常见问题及解决方案二、交换技术1. 交换技术基础2. 交换技术分类3. 广播域相关概念4. ARP 协议5. 三层交换机6. VLAN（虚拟局域网） 三、路由技术1. 路由器端口类型及功能2. 路由器功能3. 路由…...

编程日记 2025/6/29 9:27:25

黑马商城-微服务笔记

认识微服务单体架构微服务架构微服务拆分服务拆分原则什么时候拆分？ ●创业型项目：先采用单体架构，快速开发，快速试错。随着规模扩大，逐渐拆分。 ●确定的大型项目：资金充足，目标明确&a…...

编程日记 2025/7/10 23:39:57

XCZU19EG-2FFVC1760I Xilinx赛灵思FPGA Zynq UltraScale+MPSoC

XCZU19EG-2FFVC1760I 属于 Zynq UltraScaleMPSoC EG（Enhanced General）系列，采用 20nm FinFET 工艺制造，该型号的速度等级为 -2（0.85V VCCINT）、工业级温度（-40℃ 至 100℃）&#xf…...

编程日记 2025/7/11 21:56:44

第六章 QT基础：3、QT的打包和部署

问题一：什么是打包和部署？ 打包和部署是将开发完成的程序分发给用户并使其能够在目标环境中运行的两个重要步骤。打包：指的是将开发完成的程序及其依赖的所有资源（如图标、配置文件、动态链接库、字体等）打包成一个可…...

编程日记 2025/7/10 12:30:22

【测试报告】幸运闪烁抽奖系统（Java+Selenium+Jmeter自动化测试）

一、项目背景幸运闪烁抽奖系统是一款基于 Spring Boot 实现的前后端分离式的网络抽奖系统，操作便捷，安全可靠。有管理员和普通用户两个角色，支持管理员创建普通用户、新建活动奖品、创建抽奖活动、进行抽奖、通过短信/邮箱通知中奖用户等功…...

编程日记 2025/7/7 18:16:55

块压缩与图片压缩优缺点对比

块压缩与图片压缩优缺点对比块压缩（Block Compression） ✅ 优点硬件加速支持直接被GPU读取，无需CPU解压显著降低内存带宽消耗（适合移动设备） 随机访问特性 44/88像素块独立压缩支持直接定位读取特定纹理区域固…...

编程日记 2025/7/7 10:02:44

C++算法（14）：K路归并的最优解法

问题描述给定K个按升序排列的数组，要求将它们合并为一个大的有序数组。例如，输入数组[[1,3,5], [2,4,6], [0,7]]，合并后的结果应为[0,1,2,3,4,5,6,7]。解决方案思路分析合并多个有序数组的高效方法是利用最小堆（优先队列&…...

编程日记 2025/7/10 6:13:23

Multi-level treemap How to build a treemap with group and subgroups. Customization Customize treemap labels, borders, color palette and more 文章目录 Multi-level treemapCustomization Treemap 数据可视化指南Treemap 的基本概念为什么使用 TreemapTreemap 的应用…...

编程日记 2025/7/9 18:01:45

2025新一代人工智能技术发展及其应用

新一代人工智能技术发展及其应用一、人工智能概述（一）定义（二）动力（三）发展脉络二、新一代人工智能技术（一）大语言模型（二）自然语言处理（三&…...

编程日记 2025/7/4 7:59:16

vue3中slot（插槽）的详细使用

在 Vue 3 中，slot（插槽）是一种强大的组件内容分发机制，它允许父组件向子组件传递内容，从而使组件的使用更加灵活。以下是关于 Vue 3 中 slot 的详细介绍一、默认插槽这是最基本的插槽形式。子组件中使用定义一个插…...

编程日记 2025/7/10 23:13:52

大模型面经 | 春招、秋招算法面试常考八股文附答案（五）

大家好，我是皮先生！！今天给大家分享一些关于大模型面试常见的面试题，希望对大家的面试有所帮助。往期回顾：大模型面经 | 春招、秋招算法面试常考八股文附答案（RAG专题一）大模型面经 | 春招、秋招算法面试常考八股文附答案（RAG专题二）大模型面经 | 春招、秋招算法…...

编程日记 2025/7/4 13:32:25

【PCB工艺】推挽电路及交越失真

推挽电路（Push-Pull Circuit）推挽电路（Push-Pull Circuit）是一种常用于功率放大、电机驱动、音频放大等场合的电路结构，具有输出对称、效率高、失真小等优点。什么是推挽电路？推挽是指：由两种极性相反的器件（如 NPN 和 PNP、NMOS 和 PMOS）交替导通，一个“推”电…...

编程日记 2025/6/29 9:28:35

接口访问数据库报错问题记录

报错信息： java.sql.SQLException: Access denied for user rootXXX.XX.XX.XX (using password: YES) 解决方法： -- 授予 root 用户从 XXX.XX.XX.XX 访问所有数据库的权限 GRANT ALL PRIVILEGES ON *.* TO 数据库用户XX.XX.XX.XXX IDENTIFIED BY 数…...

编程日记 2025/7/5 14:13:01

神经网络相关内容

划分数据集以及模型定义 def data_split(datax, datay, val_size 0.1, test_size 0.05):输入：datax datay 输出：trainx, valx, testx, trainy, valy, testy, 分别按比例得到训练集、验证集、测试集# 构建数据集pos_test int(len(datax) * (1 - test_…...

编程日记 2025/7/6 19:21:11

python项目实战-后端个人博客系统

本文分享一个基于 Flask 框架开发的个人博客系统后端项目，涵盖用户注册登录、文章发布、分类管理、评论功能等核心模块。适合初学者学习和中小型博客系统开发。一、项目结构 blog │ app.py │ forms.py │ models.py │ ├───instance │ blog.d…...

编程日记 2025/7/10 5:50:42

谷歌搜索索引编译中的重定向错误解决方案

谷歌搜索索引编译中的重定向错误解决方案在处理谷歌搜索引擎优化（SEO）过程中遇到的重定向错误问题时，了解其根本原因并采取适当措施至关重要。以下是针对常见重定向错误及其解决方案的具体分析： 1. 滥用301和302重定向滥用永…...

编程日记 2025/7/8 14:17:01

OpenCV 中的角点检测方法详解

文章目录引言1. Harris角点检测原理1.1 什么是角点？1.2 Harris算法的核心思想1.3 角点、边缘和平坦区域的区分 2. OpenCV实现Harris角点检测3. 总结引言在计算机视觉和图像处理中，特征点检测（Feature Detection）是一个关键任务…...

编程日记 2025/7/11 17:07:30

【开源】STM32HAL库驱动ST7789_240×240（硬件SPI+软件SPI）

项目开源链接 github主页https://github.com/snqx-lqh本项目github地址https://github.com/snqx-lqh/STM32F103C8T6HalDemo作者 VXQinghua-Li7 📖 欢迎交流如果开源的代码对你有帮助，希望可以帮我点个赞👍和收藏项目说明最近调试了一款1…...

编程日记 2025/7/7 2:27:09

区块链技术在物联网中的应用：构建可信的智能世界

在当今数字化时代，物联网（IoT）和区块链技术正成为推动科技发展的两大重要力量。物联网通过连接设备实现数据的共享和交互，而区块链则以其去中心化、不可篡改的特性，为物联网的安全性和可信度提供了强大的保障。本文将探…...

编程日记 2025/7/12 12:20:26

uniapp实现app自动更新

uniapp实现app自动更新： 实现步骤： 需要从后端读取最新版本的相关信息前端用户进入首页的时候，需要判断当前版本与后端返回来的版本是否一致，不一致且后端版本大于当前版本的话，就需要提示用户是否需要更新&#xff…...

编程日记 2025/7/7 6:49:45

智能滚动抽奖--测试报告

目录一、项目背景二、项目功能三、测试计划一）单元集成测试： 二）功能测试： 三）自动化测试： 四）存在问题五）测试结果评估四、总结一、项目背景 1.随着数字营销的兴起&…...

编程日记 2025/7/8 8:43:14

天梯-这是字符串题

隐式转换隐式转换是指编译器在没有显式提示的情况下，自动将一种数据类型转换为另一种数据类型。这种转换是语言规范允许的，并且通常是为了让代码更简洁、更自然。隐式转换的类型字符类型（ char ）可以隐式转换为其对应的ASCII码值…...

编程日记 2025/7/11 8:41:03

第六章 QT基础：4、QT的TCP网络编程

一、TCP 通信原理简介 TCP（Transmission Control Protocol）是一种面向连接的可靠通信协议，主要特性如下： [!NOTE] 三次握手建立连接可靠传输：顺序、无丢包面向流：数据无结构边界适用场景&#xff1a…...

编程日记 2025/7/7 12:54:50

Windows 各版本查找计算机 IP 地址指南

IP 地址是互联网协议地址 (Internet Protocol Address) 的缩写，它是分配给连接到使用互联网协议进行通信的网络的每个设备的数字标签，用于在网络中唯一标识该设备。查找您计算机的 IP 地址对于网络故障排除、配置网络设置、远程访问以及进行其他网络相关…...

编程日记 2025/7/9 5:59:51

程序员思维体操：TDD修炼手册

程序员思维体操：TDD修炼手册 ——从"先写代码"到"测试先行"的认知革命一、重新认识TDD：不仅仅是写测试什么是TDD（测试驱动开发） TDD其实很简单，不要看名字很高级复杂，传统开发是直…...

编程日记 2025/6/29 11:21:16

Java 实现SpringContextUtils工具类，手动获取Bean

SpringContextUtils 工具类实现下面是一个完整的 Spring 上下文工具类实现，用于从 Spring 容器中获取 Bean。这个工具类考虑了线程安全、性能优化和易用性，并提供了多种获取 Bean 的方式。完整实现代码 import org.springframework.beans.BeansExce…...

编程日记 2025/7/12 0:00:25